Take Control of Your Indoor Air

May 12, 2014

ImageBy John P. Lapotaire, CIEC

Indoor Air Quality (IAQ) is a hot topic today as more of us are acquiring allergies.  We seem to be inundated with allergy statistics graphs and charts reminding us that we can only expect more of the same.  So what can we do to create our own little safe house or sanctuary?  We can take control of the Indoor Air of our homes.  The outdoor Air Quality will change with the seasons and we will need to adjust to the varying allergens introduced into the air.  But when you get home you can relax and enjoy your Indoor Air Quality if you follow a few simple housekeeping suggestions.

We should first understand that Indoor Air Quality is the effect the air inside your home has on you and your family.  Good IAQ means the air in your home has no unwanted gases or particulates at concentrations that could negatively affect you and your family.  That leaves us with poor IAQ which occurs when gasses or particulates are present at an excessive concentration in your home and affects the satisfaction or health of you and your family.

IAQ isn’t that hard to understand or identify.  We can all tell the difference between a cool mountain meadow and a city landfill. Good IAQ, Poor IAQ.  Everything else lies somewhere between the two.  What separates the good from the bad are 3 basic areas of indoor air pollutants described by the Centers for Disease Control and Prevention (CDC) as Particulates, Bioaerosols and Volatile Organic Compounds (VOC’s).  What makes up the air in your home are varying amounts of these three pollutants.

The CDC describes the three pollutants as; Particulates are common indoor air particulates including dirt, dust, fibers, tobacco smoke, and fireplace or wood stove soot. These airborne particles can range from 0.1 microns in size to 100 microns in size.  Bioaerosols are microorganisms or particles, gases, vapors, or fragments of biological origin (i.e., alive or released from a living organism) that are in the air. Bioaerosols are everywhere in the environment. Volatile Organic Compounds (VOC’s) are carbon-based chemicals that easily evaporate at room temperature. Some VOC’s have odors other VOC’s have none. Odor does not indicate the level of risk. There are thousands of different VOC’s produced and used in our daily lives.

To take control of these three pollutants that can create poor indoor air quality in your home I have created 4 primary areas that you can address that will have an immediate impact on the homes indoor air quality.
1.Particulates
2.Humidity
3.Filtration
4.House Keeping.

Let’s start with Particulates. Particulates accumulate in the home from both inside and outside sources that can include:  Some of the common Indoor Particulate Sources include:
o Pet dander
o Candles
o Incense
o Perfume
o House Plants
o Fungal spores
o Pollen
o Tobacco smoke

These sources can be controlled and or eliminated from a home by controlling the source.  That means no smoking in the home.  No air fresheners, candles or incense, these introduce particulates to the home and mask air quality issues that should be addressed directly, not hidden by air fresheners.  I would minimize house plants including plastic and silk.  Live plants live in nice damp soil that is a breeding ground for fungus and mold which can lead to the introduction of spores and plastic and silk plants can hold onto particulate releasing them each time they are disturbed.  Unfortunately these plastic and silk plants are rarely cleaned and the amount of particulates they can introduce when disturbed is substantial.

Next you’ll need to keep a healthy level of humidity in your home.  Dust mites and mold love moisture so keeping humidity around 30%-50% will help keep dust mites and other allergens under control.  The addition of a humidistat and dehumidifier can greatly improve the indoor air quality of your home.  The humidistat turns on the homes air conditioning when the humidity reaches the set relative humidity (preferably not higher than 55%rh) just as the thermostat activates the homes air conditioning when the temperature reaches a set temperature (preferably not higher than 76°F).

Maintaining the proper humidity level helps reduce moisture in the indoor air and can effectively control allergens.  

High humidity levels in Florida can produce musty odor and/or a clammy feeling to the air in the summer and condensation on windows in the winter.

Often the principal source of higher humidity in a home is a family’s living habits. One person’s breathing produces 1/4 cup of water per hour, cooking for a family of four produces approximately five pints of water in 24 hours, showering puts 1/2 pint of water into the air.  Bathing puts 1/8 pint of water into the air.  Adding only four to six pints of water to the air raises the relative humidity in a 1,000 square foot home from 15 to 60 percent, assuming the temperature is constant.

Next on our list is Filtration.   Each time the air conditioning system cycles air into the home, armies of particulates are propelled through the supply ducts and discharged throughout your home into the air your family breathes.  More specifically the air you breathe is filled with the particulates allowed to pass through your air conditioning filter.  The filtration you choose has a tremendous affect on your indoor air quality so you should use the highest level of filtration that your system allows.

There are many filters available on the market today.  The most common are the one inch filters found in supermarkets, hardware stores and home supply retailers. All these filters guarantee a percentage of effectiveness, but that can be misleading. 

Standard throwaway filters are only designed to protect the air handler. And have little or no capability of collecting fine particles.  Washable Filters are very restrictive to airflow and are difficult to clean thoroughly and are rarely maintained at the proper level.  Electronic Air Cleaners are 95% efficient at .3 microns when new and clean. They reduce in efficiency very quickly as they load with particles and are difficult to clean thoroughly.  Many home owners just don’t take the time to properly clean these clean these filters on a regular basis, so they rarely works at the efficiency they were designed for.  Large 4 to 5 Inch Media Filters have a large amount of filter surface and allow for good air flow.  They can collect a large amount of dust and particles above one micron in size and most don’t have to be replaced for 6 to 12 months.  These filters are typically MERV rated at 8 to 11.

So now a I know you are asking Who is Merv and should I trust him with my filter? Well Merv isn’t a “He” MERV is an industry standard.  A standard rating system that can be used to compare filters made by different companies.   The MERV (Minimum Efficiency Reporting Value) rating of a filter describes the size of the holes in the filter that allow air to pass through.  In a nut shell the higher the MERV rating, the smaller the holes in the filter, the higher the efficiency.  Residential filters commonly have MERV ratings of 1-11. The higher the MERV rating, the more efficient the filter is, and the more particles it can filter.
o A MERV rating of 6 means the filter is 35% to 50% minimum efficient at capturing particles, sized 3.0-10.0 microns.
o A MERV rating of 7 means the filter is 50% to 70% minimum efficient at capturing particles, sized 3.0-10.0 microns.
o A MERV rating of 8 means the filter is 70% minimum efficient at capturing particles, sized 3.0-10.0 microns.
o A MERV rating of 11 means the filter is 85% minimum efficient at capturing particles, sized 3.0-10.0 microns. 

Now for the House keeping side of air quality improvement.   You first to reduce the humidity in the home by using your range, bathroom and cooking exhaust fans.  You should also ensure that they are vented to the outside.  You should check your dryer exhaust vent regularly to ensure it isn’t clogged.  Reduce the number of plants in the home and/or water them less so they release less water vapor.  And you can add a humidistat and mechanical dehumidifier to your air conditioning system.  So IAQ is a piece of cake.

Now you need to get rid of those pesky particulates. The key to that is to Collect and Remove.  You can collect and remove particles by using a HEPA vacuum.  Don’t forget to vacuum all porous surfaces including upholstered furniture. For best results, vacuum two or more times each week and change your HEPA filter regularly.  On tile floors you can collect and remove particles by mopping which will collect the dust that your HEPA vacuuming leaves behind. You can skip the soaps and cleaners and just use plain water to capture any lingering dust or allergens. There are also new microfiber mops that reportedly capture more dust and dirt than traditional mops and don’t require any cleaning solutions whatsoever.  Okay there may be a bit of an investment here for a HEPA vacuum, but I can assure you it will be worth it.

For the particle dust build up within the home you will need to collect and remove it as well.  For most people this means dusting using a simple feather duster, or a cloth of some kind, and some kind of dusting spray. This just relocates the dust particulates and introduces bioaerosols & VOC’s into the air.  Remember the key is to collect and remove not relocate.   I recommend using the new microfiber dust cloth that can capture more dust and dirt than traditional fibers and don’t require any cleaning solutions whatsoever.

To help prevent the particulates from entering the home, place large floor mats at every door. People track in all sorts of particles via the dirt on their shoes. A door mat reduces the amount of dirt, pesticides, and other pollutants from getting into your home. If the mat is big enough, even those who don’t wipe their shoes will leave most pollutants on the mat — not the floors in the home.

Don’t forget to change your air conditioning filters every 30 days or as prescribed by the Manufacturer.  Not maintaining your air conditioning filter is a major source of indoor air problems.  Some of the higher MERV rated media filters can be changed as infrequently as every 6 months.   While you are changing that filter check you’re A/C drain line and every 3 months flush it with an algae control cleaner to prevent clogging.

Remember to keep your home dry: Control humidity levels between 35% and 50% to prevent dust mites and an indoor environment that can lead to mold growth.  Fix any leaks you have in your home as soon as you find them.  If you have a flood, take immediate action and dry the area out, including all affected furnishings, within 48 hours to prevent mold growth.

So when asked what you can do about the “Air You Breathe” you will have plenty to say because you know what is in the air you breathe.  And you know that Good IAQ for people already suffering from allergies can reduce the symptoms of those allergies, often reduce medications for allergies, and lead to more relaxing sleep.  You also know that Good Indoor Air Quality can have a substantial impact on our children by preventing allergies, delaying the occurrence of an allergy, or the reduction of allergy symptoms.

Now you can say “Healthier Air Starts Here!”

To learn more about Mr. Lapotaire or Indoor Air Quality Solutions & Microshield Environmental Services, LLC, please visit www.FloridaIAQ.com, email info@FloridaIAQ.com or call (407) 383-9459.

About Indoor Air Quality Solutions & Microshield Environmental Services, LLC

Since 2001, Florida residents have turned to the indoor environmental experts at Indoor Air Quality Solutions & Microshield Environmental Services, LLC.  The family owned and operated companies, based in the Orlando area, offer a comprehensive approach to identifying and correcting comfort and indoor air quality problems.  Their expert staff utilizes the latest technologies and industry recognized standards to identify and resolve indoor environmental issues.

John P. Lapotaire, CIEC

#IAQS

 


Chemical Free Mold Remediation

May 12, 2014

ImageMold Remediation is the process of removing mold while protecting unaffected areas of a home or office from unnecessary cross contamination.  At no time is it necessary to KILL Mold.  Mold must be Removed regardless of its ability to germinate and grow into a colony.  The safest way to end the life cycle of mold is to simply eliminate the water source that is allowing the mold to grow.  Removing the water source is far safer that using Biocides and you will still need to remove the mold regardless of the molds viability.

Remember ALL Mold Remediation Should be Chemical Free Mold Remediation.

The Florida Department of Health

The goal should be to remove mold growth by cleaning or removing moldy materials. Dead mold can still pose health risks if you are exposed.

Ozone irritates lungs, and is not likely to be effective at addressing an indoor mold problem. No one should expose themselves or others to ozone on purpose. Address the cause of the mold (usually moisture) and then remove the mold by cleaning surfaces or removing moldy materials.

We know that we’ll never be able to eliminate all of the mold from within our home or office.  But we can prevent it from growing within our home or office by eliminating the moisture that supports its growth.  The sources of moisture that support mold growth include elevations of humidity above 60%, plumbing leaks, and building envelope failure such as roof and window leaks.

If mold is found to be growing in your home or office due to an elevation in humidity, leak, or an unfortunate water loss, you need to first identify the moisture source that is supporting the mold growth to correct and prevent continued mold growth. Then, collect and remove the mold and water damaged building material from the indoor environment.

Mold only needs a few things to grow and multiply:

  • Nutrients (food – almost anything)
  • A suitable place to grow (almost anywhere)
  • Moisture

Eliminating any one will prevent the mold from growing.  What you’re left with is the mold that can become airborne and directly affect the occupants.  This mold must be collected and removed from your home or office.

We know that there is no shortage of “Quick Fix” Ozone or Chemical using mold remediators out there that will chemically fog your home or office and affordably “Kill” your mold, but guess what?  Your mold is still there.  Without the moisture you corrected the mold wouldn’t have regrown anyway.  Now you have the mold (allergen) covered in a chemical (poisonous both to the mold and humans) and is now a “poisonous allergen” waiting to become airborne and potentially impact the occupants.

There is no need to expose anyone to Ozone, Hydroxyls, Biocides, Disinfectants, Fungicides, Anti-microbials, and Encapsulants during Mold Remediation.

Our Mold Remediation Protocols are written to protect or clients from the dust up of mold during the removal and the unnecessary use of chemicals.  Our Protocols are designed to collect and remove the mold from your home or office without the use of chemicals.

Our goal is to protect our Clients from exposure to Ozone, Hydroxyls, Biocides, Disinfectants, Fungicides, Anti-microbials, and Encapsulants during Mold Remediation.  The unnecessary use of these products are Forbiden.

All of our Mold Remediation Protocols include the following statement:

Ozone, Hydroxyls, Biocides, Disinfectants, se Fungicides, Anti-microbials, and Encapsulants must not be used unless specified in this protocol.  If chemical use is specified in this protocol, the chemicals can only be applied in the specific areas identified in this protocol.

If chemical use is specified in this protocol the chemicals will be used for the purpose of Disinfection of the Category 3 water damaged areas and not for the purpose of Killing or Removing Mold.

If the remediation contractor would like to apply chemicals in any way not specified in this protocol, the Remediator must obtain written permission from the IAQ Solutions IEP.

IICRC S-520
Source removal of mold contamination should always be the primary means of remediation.  The Indiscriminant use of antimicrobial products, coatings, sealants, and cleaning chemicals is not recommended.

NYCDH New York City Department of Health
“The use of gaseous, vapor-phase, or aerosolized biocides for remedial purposes is not recommended. The use of biocides in this manner can pose health concerns for people in occupied spaces of the building and for people returning to the treated space if used improperly.

AIHA American Industrial Hygiene Association
The goal of remediation is removal of mold and the moisture source because:
    a) biocides do not alter mycotoxins or allergens;
    b) it is generally not possible to get 100 percent kill with biocides; and
    c) because of (b), the newly deposited spores, re-growth will occur after the biocides if moisture returns

OSHA Occupational Safety and Health Administration
The use of a biocide, such as chlorine bleach, is not recommended as a routine practice during mold remediation, although there may be instances where professional judgment may indicate its use (for example, when immuno-compromised individuals are present). In most cases, it is not possible or desirable to sterilize an area, as a background level of mold spores comparable to the level in outside air will persist. However, the spores in the ambient air will not cause further problems if the moisture level in the building has been corrected. Biocides are toxic to animals and humans, as well as to mold.

U.S. EPA Environmental Protection Agency
“The purpose of mold remediation is to remove the mold to prevent human exposure and damage to building materials and furnishings. It is necessary to clean up mold contamination, not just to kill the mold. Dead mold is still allergenic, and some dead molds are potentially toxic.  Whether dead or alive, mold is allergenic, and some molds may be toxic.

To learn more about Mr. Lapotaire or Indoor Air Quality Solutions & Microshield Environmental Services, LLC, please visit www.FloridaIAQ.com, email info@FloridaIAQ.com or call (407) 383-9459.

About Indoor Air Quality Solutions & Microshield Environmental Services, LLC

Since 2001, Florida residents have turned to the indoor environmental experts at Indoor Air Quality Solutions & Microshield Environmental Services, LLC.  The family owned and operated companies, based in the Orlando area, offer a comprehensive approach to identifying and correcting comfort and indoor air quality problems.  Their expert staff utilizes the latest technologies and industry recognized standards to identify and resolve indoor environmental issues.

John P. Lapotaire, CIEC

#IAQS

 

 

 


Chemical Free Mold Remediation

May 12, 2014

Mold Remediation is the process of removing mold while protecting unaffected areas of a home or office from unnecessary cross contamination.  At no time is it necessary to KILL Mold.  Mold must be Removed regardless of its ability to germinate and grow into a colony.  The safest way to end the life cycle of mold is to simply eliminate the water source that is allowing the mold to grow.  Removing the water source is far safer that using Biocides and you will still need to remove the mold regardless of the molds viability.

So Remember ALL Mold Remediation Should be Chemical Free Mold Remediation.

The Florida Department of Health
The goal should be to remove mold growth by cleaning or removing moldy materials. Dead mold can still pose health risks if you are exposed.

Ozone irritates lungs, and is not likely to be effective at addressing an indoor mold problem. No one should expose themselves or others to ozone on purpose. Address the cause of the mold (usually moisture) and then remove the mold by cleaning surfaces or removing moldy materials.

We know that we’ll never be able to eliminate all of the mold from within our home or office.  But we can prevent it from growing within our home or office by eliminating the moisture that supports its growth.  The sources of moisture that support mold growth include elevations of humidity above 60%, plumbing leaks, and building envelope failure such as roof and window leaks.

If mold is found to be growing in your home or office due to an elevation in humidity, leak, or an unfortunate water loss, you need to first identify the moisture source that is supporting the mold growth to correct and prevent continued mold growth. Then, collect and remove the mold and water damaged building material from the indoor environment.

Mold only needs a few things to grow and multiply:

    Nutrients (food – almost anything)
    A suitable place to grow (almost anywhere)
    Moisture

Eliminating any one will prevent the mold from growing.  What you’re left with is the mold that can become airborne and directly affect the occupants.  This mold must be collected and removed from your home or office.

We know that there is no shortage of “Quick Fix” Ozone or Chemical using mold remediators out there that will chemically fog your home or office and affordably “Kill” your mold, but guess what?  Your mold is still there.  Without the moisture you corrected the mold wouldn’t have regrown anyway.  Now you have the mold (allergen) covered in a chemical (poisonous both to the mold and humans) and is now a “poisonous allergen” waiting to become airborne and potentially impact the occupants.

There is no need to expose anyone to Ozone, Hydroxyls, Biocides, Disinfectants, Fungicides, Anti-microbials, and Encapsulants during Mold Remediation.

Our Mold Remediation Protocols are written to protect or clients from the dust up of mold during the removal and the unnecessary use of chemicals.  Our Protocols are designed to collect and remove the mold from your home or office without the use of chemicals.

Our goal is to protect our Clients from exposure to Ozone, Hydroxyls, Biocides, Disinfectants, Fungicides, Anti-microbials, and Encapsulants during Mold Remediation.  The unnecessary use of these products are Forbiden.

All of our Mold Remeiation Protocols include the following statement:

Ozone, Hydroxyls, Biocides, Disinfectants, se Fungicides, Anti-microbials, and Encapsulants must not be used unless specified in this protocol.  If chemical use is specified in this protocol, the chemicals can only be applied in the specific areas identified in this protocol.

If chemical use is specified in this protocol the chemicals will be used for the purpose of Disinfection of the Category 3 water damaged areas and not for the purpose of Killing or Removing Mold.

If the remediation contractor would like to apply chemicals in any way not specified in this protocol, the Remediator must obtain written permission from the IAQ Solutions IEP.

IICRC S-520
Source removal of mold contamination should always be the primary means of remediation.  The Indiscriminant use of antimicrobial products, coatings, sealants, and cleaning chemicals is not recommended.

NYCDH New York City Department of Health
“The use of gaseous, vapor-phase, or aerosolized biocides for remedial purposes is not recommended. The use of biocides in this manner can pose health concerns for people in occupied spaces of the building and for people returning to the treated space if used improperly.

AIHA American Industrial Hygiene Association
The goal of remediation is removal of mold and the moisture source because:

  • biocides do not alter mycotoxins or allergens;
  • it is generally not possible to get 100 percent kill with biocides; and
  • the newly deposited spores, re-growth will occur after the biocides if moisture returns


OSHA Occupational Safety and Health Administration
The use of a biocide, such as chlorine bleach, is not recommended as a routine practice during mold remediation, although there may be instances where professional judgment may indicate its use (for example, when immuno-compromised individuals are present). In most cases, it is not possible or desirable to sterilize an area, as a background level of mold spores comparable to the level in outside air will persist. However, the spores in the ambient air will not cause further problems if the moisture level in the building has been corrected. Biocides are toxic to animals and humans, as well as to mold.

U.S. EPA Environmental Protection Agency
“The purpose of mold remediation is to remove the mold to prevent human exposure and damage to building materials and furnishings. It is necessary to clean up mold contamination, not just to kill the mold. Dead mold is still allergenic, and some dead molds are potentially toxic.  Whether dead or alive, mold is allergenic, and some molds may be toxic.

 

For more information about the Indoor Air Quality Association, please visit www.IAQA.org.

To learn more about Mr. Lapotaire or Indoor Air Quality Solutions & Microshield Environmental Services, LLC, please visit www.FloridaIAQ.com, email info@FloridaIAQ.com or call (407) 383-9459.

About Indoor Air Quality Solutions & Microshield Environmental Services, LLC

Since 2001, Florida residents have turned to the indoor environmental experts at Indoor Air Quality Solutions & Microshield Environmental Services, LLC.  The family owned and operated companies, based in the Orlando area, offer a comprehensive approach to identifying and correcting comfort and indoor air quality problems.  Their expert staff utilizes the latest technologies and industry recognized standards to identify and resolve indoor environmental issues.

John P. Lapotaire, CIEC

#IAQS

 


<span>%d</span> bloggers like this: